Image 1 of 5
Image 2 of 5
Image 3 of 5
Image 4 of 5
Image 5 of 5
UHMW Snow Clearing Edges for the John Deere SPC8 and SPC10, Replaces T244854, T244858, T244860, T244864
Free Ground Shipping to the lower 48 States
These edges are shipped in their full length of 8 or 10 feet so the extra shipping costs are reflected in the prices for each item.
If you have a John Deere SPC8 or SPC10 Snow Pusher and would like to replace the steel wear edge with a UHMW wear edge to stop the pavement surface abrasion and wear on the asphalt seal coatings, etc., we make these UHMW edges for you. These replace either the main pusher steel edge or we also make a UHMW edge for the back drag arm on these pushers.
Reasons to switch from Steel to UHMW edges for clearing pavement include;
UHMW is very low surface friction and is much easier on the pavement surface.
UHMW doesn’t leave behind metal shards that lead to rust stains in the pavement.
UHMW is less likely to damage the pavement surface, the way steel does.
UHMW pushes easier, has the lowest surface friction of any material and also eliminates the loud scraping and screeching sounds of steel on the pavement.
UHMW wears extremely well when used properly and appropriately. In many cases, the UHMW edge will provide a similar wear life to the mild steel edges on many snow clearing machines.
We offer two thicknesses of UHMW depending upon the customers needs. These thicknesses are 1.25” thick for our Heavy Duty UHMW edge and 1.50” thick for our Severe Duty UHMW edges. Here are the details for these replacement UHMW wear edges.
Heavy Duty UHMW Wear Edges for the
SPC8 and SPC10 Snow Pushers
The main pusher edge is 8” tall and 1.25” thick, made from UHMW.
The edge mounting holes are machined into the UHMW in the center.
This makes all UHMW wear edges double sided.
The edges mount using 1/2” cap screws with large fender washers under the bolt head. Flat washers, lock washers and nuts are on the back side.
Hardware is included in the purchase price to mount your new UHMW edge.
Extreme Duty UHMW Wear Edges
The main pusher edge is 10” tall, 1.5” thick, made from UHMW
The edge has two rows of parallel holes mounted 4” from the top and bottom edges, providing two mounting positions for each UHMW edge.
All of the Extreme Duty UHMW wear edges are double sided as well as having dual mounting positions, to get the most wear from the edge.
The edges mount using 1/2” cap screws with large fender washers under the bolt head. Flat washers, lock washers and nuts are on the back side.
Hardware is included in the purchase price to mount your new UHMW edge.
These UHMW Edges are made when ordered to make sure to accommodate any custom order requests for these items.
Please note, the Heavy Duty and Extreme Duty UHMW Edges for the SPC8 and SPC10 Snow Pushers are made when ordered. Please allow 12 to 15 business days from when your order is placed for us to ship your order.
If you need an edge for these Snow Pushers more quickly, we are able to ship our rubber edges within a few days of your order as we keep the rubber units in stock for the SPC8 and SPC10 at most times.
Please note, the main snow pusher edge and the back drag edges are NOT Interchangeable. Please order the specific Edge you need, in the proper duty service level (either Heavy Duty or Severe Duty).
To be clear, you can order the following UHMW edges for either the SPC8 or SPC10 Deere Snow Pushers;
Heavy Duty Main Pusher UHMW edge for the main pusher edge which clears snow when pushing forward.
Heavy Duty Back Drag UHMW edge for the back drag clearing arm.
Extreme Duty Main Pusher UHMW edge for the main pusher edge which clears snow when pushing forward.
Extreme Duty Back Drag Pusher UHMW for the back drag clearing arm.
Our UHMW edges ship with new hardware to mount on your snow pusher.
Who should order a UHMW edge for their snow pusher?
The snow pusher operator that needs to protect their pavement from surface abrasion damage from using a steel edge.
The snow pusher operator who wants to scrape hard packed snow and ice from the pavement, but not harm the pavement as the steel edge does.
The snow pusher operator who wants to eliminate the scraping and screeching sound of steel on the pavement.
The snow pusher operator who deals with steep paved slopes and is
Who should NOT order a UHMW edge for their snow pusher?
Those clearing very rough and uneven surfaces with fractured pavement.
Those who need to push snow across lawn or grass areas.
Those who are dealing with fragile pavement surfaces such as new asphalt that has not been finished with the top coat or new asphalt that hasn’t had a chance to cure and “grey in”, which usually takes 6 to 12 months from when its installed.
Any pavement surface that is easily damaged such as colored and or imprinted concrete, special exposed aggregate surfaces used on some sidewalks or around swimming pools, etc. or any surface such as tile or ceramic surfaces that are likely to be damaged by hard scraping efforts. (Yes, we have some customers who drives, walks, foyers and portico areas use these fragile surface materials).
Questions or need Help?
Contact us via phone at
269.428.9932 Office
or by email at
Thank You……
Free Ground Shipping to the lower 48 States
These edges are shipped in their full length of 8 or 10 feet so the extra shipping costs are reflected in the prices for each item.
If you have a John Deere SPC8 or SPC10 Snow Pusher and would like to replace the steel wear edge with a UHMW wear edge to stop the pavement surface abrasion and wear on the asphalt seal coatings, etc., we make these UHMW edges for you. These replace either the main pusher steel edge or we also make a UHMW edge for the back drag arm on these pushers.
Reasons to switch from Steel to UHMW edges for clearing pavement include;
UHMW is very low surface friction and is much easier on the pavement surface.
UHMW doesn’t leave behind metal shards that lead to rust stains in the pavement.
UHMW is less likely to damage the pavement surface, the way steel does.
UHMW pushes easier, has the lowest surface friction of any material and also eliminates the loud scraping and screeching sounds of steel on the pavement.
UHMW wears extremely well when used properly and appropriately. In many cases, the UHMW edge will provide a similar wear life to the mild steel edges on many snow clearing machines.
We offer two thicknesses of UHMW depending upon the customers needs. These thicknesses are 1.25” thick for our Heavy Duty UHMW edge and 1.50” thick for our Severe Duty UHMW edges. Here are the details for these replacement UHMW wear edges.
Heavy Duty UHMW Wear Edges for the
SPC8 and SPC10 Snow Pushers
The main pusher edge is 8” tall and 1.25” thick, made from UHMW.
The edge mounting holes are machined into the UHMW in the center.
This makes all UHMW wear edges double sided.
The edges mount using 1/2” cap screws with large fender washers under the bolt head. Flat washers, lock washers and nuts are on the back side.
Hardware is included in the purchase price to mount your new UHMW edge.
Extreme Duty UHMW Wear Edges
The main pusher edge is 10” tall, 1.5” thick, made from UHMW
The edge has two rows of parallel holes mounted 4” from the top and bottom edges, providing two mounting positions for each UHMW edge.
All of the Extreme Duty UHMW wear edges are double sided as well as having dual mounting positions, to get the most wear from the edge.
The edges mount using 1/2” cap screws with large fender washers under the bolt head. Flat washers, lock washers and nuts are on the back side.
Hardware is included in the purchase price to mount your new UHMW edge.
These UHMW Edges are made when ordered to make sure to accommodate any custom order requests for these items.
Please note, the Heavy Duty and Extreme Duty UHMW Edges for the SPC8 and SPC10 Snow Pushers are made when ordered. Please allow 12 to 15 business days from when your order is placed for us to ship your order.
If you need an edge for these Snow Pushers more quickly, we are able to ship our rubber edges within a few days of your order as we keep the rubber units in stock for the SPC8 and SPC10 at most times.
Please note, the main snow pusher edge and the back drag edges are NOT Interchangeable. Please order the specific Edge you need, in the proper duty service level (either Heavy Duty or Severe Duty).
To be clear, you can order the following UHMW edges for either the SPC8 or SPC10 Deere Snow Pushers;
Heavy Duty Main Pusher UHMW edge for the main pusher edge which clears snow when pushing forward.
Heavy Duty Back Drag UHMW edge for the back drag clearing arm.
Extreme Duty Main Pusher UHMW edge for the main pusher edge which clears snow when pushing forward.
Extreme Duty Back Drag Pusher UHMW for the back drag clearing arm.
Our UHMW edges ship with new hardware to mount on your snow pusher.
Who should order a UHMW edge for their snow pusher?
The snow pusher operator that needs to protect their pavement from surface abrasion damage from using a steel edge.
The snow pusher operator who wants to scrape hard packed snow and ice from the pavement, but not harm the pavement as the steel edge does.
The snow pusher operator who wants to eliminate the scraping and screeching sound of steel on the pavement.
The snow pusher operator who deals with steep paved slopes and is
Who should NOT order a UHMW edge for their snow pusher?
Those clearing very rough and uneven surfaces with fractured pavement.
Those who need to push snow across lawn or grass areas.
Those who are dealing with fragile pavement surfaces such as new asphalt that has not been finished with the top coat or new asphalt that hasn’t had a chance to cure and “grey in”, which usually takes 6 to 12 months from when its installed.
Any pavement surface that is easily damaged such as colored and or imprinted concrete, special exposed aggregate surfaces used on some sidewalks or around swimming pools, etc. or any surface such as tile or ceramic surfaces that are likely to be damaged by hard scraping efforts. (Yes, we have some customers who drives, walks, foyers and portico areas use these fragile surface materials).
Questions or need Help?
Contact us via phone at
269.428.9932 Office
or by email at
Thank You……