John Deere SP8c or SP10c Snow Pusher Rubber Edge, T244854 or T244860

from $755.00
Size:

Free Ground Shipping in the Lower 48 States

This is for the Main Rubber Edge used for clearing snow on the SP8c and SP10C Deere Snow Pushers. If you need a Back Drag Rubber edge for your Deere SPC8 or SPC10 Snow Pushers, make sure to refer to our Back Drag edge Listing for that machine.

The main rubber edge and the back drag rubber edge are made differently and are not interchangeable.

We offer two duty levels of rubber edge for your John Deere SP8c or SP10c snow pusher.

Our Heavy Duty Rubber edge is designed to be equal or exceed the original rubber edge it is replacing.

Our Extreme Duty Rubber edge is designed for those who demand more from their rubber edge. The Extreme Duty Rubber Edge is taller, thicker and provides a longer wear duration than the Heavy Duty Edge. For those who want to get more use from the snow pusher between edge replacements.

Do you need Back Drag Rubber edges for your SP8c or SP10c? We have those listed in another listing here on our site under SP8c and SP10c Rubber Back Drag edges.

If you need to replace the steel clamping straps that hold your rubber edges on the Deere SP8c and SP10c snow pushers, we offer our UHMW clamping straps under another listing on this site.

Heavy Duty front rubber snow pusher edge for these heavy duty use pushers.

The SP8C uses rubber edge T244854

The SP10c uses the rubber edge T244860

Here are the features of this Heavy Duty Snow Pusher Rubber Edge.

  • Heavy Duty 8” tall by 1” thick rubber edge

  • The SP8c Heavy Duty rubber edge is 90” wide for the 96” wide machine.

  • The SP10 Heavy Duty rubber edge is 114” wide for the 120” wide machine.

  • Mounting holes are center cut by machine for easy installation.

  • Machine cut mounting holes down the center of the edge make this a double sided wear edge for maximum wear and use life.

  • Round mounting holes make sure the edge stays in place even with down pressure and scraping action on the edge.

  • SPC8 Ships with 15 new 1/2” x 2.5” Cap Screw bolts, flat washers, lock washers and nuts for installation.

  • SPC10 ships with 19 new 1/2” x 2.5” Cap screw bolts, flat washers, lock washers and nuts for installation.

Extreme Duty front rubber snow pusher edge is available for those who want a thicker, tougher and longer lasting rubber edge for maximum use. Designed for the toughest use conditions;

Here are the Features of this Extreme Duty Snow Pusher Rubber Edge.

  • Extreme Duty 10” tall by 1.5” thick rubber edge.

  • This Extreme Duty Rubber Edge is 2” taller and 1/2” thicker than the Heavy Duty edge.

  • Designed to be the most durable, longest lasting rubber edge we make for this snow pusher.

  • The additional 1/2” of material thickness provides extra durability for this edge.

  • Two rows of parallel 5/8” mounting holes are center cut by machine for easy installation.

  • With the mounting holes in two rows spaced 4” from each edge, you have two mounting positions for this edge on each wear side.

  • Install this edge at the normal mounting position to place the rubber at the same height as the original rubber. But you also have another row of holes centered 2” above this standard mounting height, so you can lower the rubber edge a second time as its used, for longer wear life.

  • Install the edge and use it for snow clearing. When the first edge wears, you can unbolt the mounting straps, lower the Extreme Duty edge to the 2nd row of mounting holes and extend the wear on this side of the pusher edge by using the additional 1” of rubber edge per side.

  • When the first side of the edge is worn down, the entire edge can be unbolted, flipped over and start with the new wear edge on the other side.

  • SPC8 Ships with 15 new 1/2” x 3” Cap Screw bolts, flat washers, lock washers and nuts for installation.

  • SPC10 ships with 19 new 1/2” x 3” Cap screw bolts, flat washers, lock washers and nuts for installation.

Please note, the purchase of our rubber edges for these snow pushers does NOT includes new clamping straps. You will reuse the steel clamping straps on your SP8c or SP10c snow pusher to hold these new rubber edges.

If, due to damage or corrosion, you need new clamping straps, new UHMW clamping straps are available in another listing on our site.

Advantage of UHMW Rubber Edge Clamping Straps include;

  • Never need painting or powder coating, the UHMW is a solid color through the edge.

  • Extremely strong and can endure some impacts without bending or breaking.

  • Lighter weight than steel, so easier to install.

  • Please see the listing for the UHMW clamping straps for more details.

Thank you for your Business. If you have questions, please contact us at

269.428.9932 Office Phone

or

SulleyBearSolutions@Gmail.com

Free Ground Shipping in the Lower 48 States

This is for the Main Rubber Edge used for clearing snow on the SP8c and SP10C Deere Snow Pushers. If you need a Back Drag Rubber edge for your Deere SPC8 or SPC10 Snow Pushers, make sure to refer to our Back Drag edge Listing for that machine.

The main rubber edge and the back drag rubber edge are made differently and are not interchangeable.

We offer two duty levels of rubber edge for your John Deere SP8c or SP10c snow pusher.

Our Heavy Duty Rubber edge is designed to be equal or exceed the original rubber edge it is replacing.

Our Extreme Duty Rubber edge is designed for those who demand more from their rubber edge. The Extreme Duty Rubber Edge is taller, thicker and provides a longer wear duration than the Heavy Duty Edge. For those who want to get more use from the snow pusher between edge replacements.

Do you need Back Drag Rubber edges for your SP8c or SP10c? We have those listed in another listing here on our site under SP8c and SP10c Rubber Back Drag edges.

If you need to replace the steel clamping straps that hold your rubber edges on the Deere SP8c and SP10c snow pushers, we offer our UHMW clamping straps under another listing on this site.

Heavy Duty front rubber snow pusher edge for these heavy duty use pushers.

The SP8C uses rubber edge T244854

The SP10c uses the rubber edge T244860

Here are the features of this Heavy Duty Snow Pusher Rubber Edge.

  • Heavy Duty 8” tall by 1” thick rubber edge

  • The SP8c Heavy Duty rubber edge is 90” wide for the 96” wide machine.

  • The SP10 Heavy Duty rubber edge is 114” wide for the 120” wide machine.

  • Mounting holes are center cut by machine for easy installation.

  • Machine cut mounting holes down the center of the edge make this a double sided wear edge for maximum wear and use life.

  • Round mounting holes make sure the edge stays in place even with down pressure and scraping action on the edge.

  • SPC8 Ships with 15 new 1/2” x 2.5” Cap Screw bolts, flat washers, lock washers and nuts for installation.

  • SPC10 ships with 19 new 1/2” x 2.5” Cap screw bolts, flat washers, lock washers and nuts for installation.

Extreme Duty front rubber snow pusher edge is available for those who want a thicker, tougher and longer lasting rubber edge for maximum use. Designed for the toughest use conditions;

Here are the Features of this Extreme Duty Snow Pusher Rubber Edge.

  • Extreme Duty 10” tall by 1.5” thick rubber edge.

  • This Extreme Duty Rubber Edge is 2” taller and 1/2” thicker than the Heavy Duty edge.

  • Designed to be the most durable, longest lasting rubber edge we make for this snow pusher.

  • The additional 1/2” of material thickness provides extra durability for this edge.

  • Two rows of parallel 5/8” mounting holes are center cut by machine for easy installation.

  • With the mounting holes in two rows spaced 4” from each edge, you have two mounting positions for this edge on each wear side.

  • Install this edge at the normal mounting position to place the rubber at the same height as the original rubber. But you also have another row of holes centered 2” above this standard mounting height, so you can lower the rubber edge a second time as its used, for longer wear life.

  • Install the edge and use it for snow clearing. When the first edge wears, you can unbolt the mounting straps, lower the Extreme Duty edge to the 2nd row of mounting holes and extend the wear on this side of the pusher edge by using the additional 1” of rubber edge per side.

  • When the first side of the edge is worn down, the entire edge can be unbolted, flipped over and start with the new wear edge on the other side.

  • SPC8 Ships with 15 new 1/2” x 3” Cap Screw bolts, flat washers, lock washers and nuts for installation.

  • SPC10 ships with 19 new 1/2” x 3” Cap screw bolts, flat washers, lock washers and nuts for installation.

Please note, the purchase of our rubber edges for these snow pushers does NOT includes new clamping straps. You will reuse the steel clamping straps on your SP8c or SP10c snow pusher to hold these new rubber edges.

If, due to damage or corrosion, you need new clamping straps, new UHMW clamping straps are available in another listing on our site.

Advantage of UHMW Rubber Edge Clamping Straps include;

  • Never need painting or powder coating, the UHMW is a solid color through the edge.

  • Extremely strong and can endure some impacts without bending or breaking.

  • Lighter weight than steel, so easier to install.

  • Please see the listing for the UHMW clamping straps for more details.

Thank you for your Business. If you have questions, please contact us at

269.428.9932 Office Phone

or

SulleyBearSolutions@Gmail.com